2014 HMP 16 STATION SWAGING LINE FOR AXLES AND OTHER LIKE SHAFTS

1-USED HMP SWAGING LINE FOR PRODUCING HOLLOW DRIVE SHAFT'S OR AXLES

MACHINE SERIAL NUMBER R10-4/UR7-4-DD-55H-AU-13 MACHINE INSTALLED NEW 2014

STK#104013 ============================================================ SPECIFICATIONS WHILE OBTAINED FROM SOURCES DEEMED RELIABLE ARE SUBJECT CHANGE WITHOUT NOTICE AND TO VERIFICATION BY BUYER:

LINE IS OFFERED "AS-IS", WHERE-IS" BUYER RESPONSIBLE FOR

REMOVAL AND LOAD OUT. THIS ENTIRE LINE WAS INSTALLED IN 2014 WITH LIMITED USE AFTER INSTALL.

ONLY 350,000 AXLES WERE PRODUCED AFTER INSTALL. CAPACITY: CURRENTLY SET UP FOR 800MM LONG SHAFTS APPROX. DIAMETER CAPACITY 4" MAX. FOR FORMING HOLLOW OR SOLID SHAFT AXLES AND OTHER LIKE CYLINDRICAL FORMS MAJOR COMPONENTS OF THE LINE ARE AS FOLLOWS: 16-STATION TRANSFER SWAGING MACHINE R10-4/UR7-4-DD-55H-AU-13

equipped with:

-automation system

-station 0 transfer station

-station 1: swaging station R10-4

-station 2: swaging station R10-4

-station 3: transfer station

-station 4: swaging station R10-4

-station 5: swaging station UR7-4-DD

-station 6: hydraulic axial forming station HU-40

-station 7: turning station-sms

-station 8: turnaround station

-station 9: swaging station R10-4

-station 10: swaging station UR7-4-DD

-station11: swaging station UR7-4-DD

-station 12: axial forming station HU-40

-station 13: turning station

-station 14: rolling station

-station 15: cleaning station

-base, hydraulic system, lubrication system, PLC controls system, etc.

Additional Features, Options:    

2.1 Noise and safety enclosure 

2.2 Drip pan  

2.3 Additional cleaning station  

2.4 Additional neck down swaging station 

Production Process on 13-Station Transfer Swaging Machine R10-4/UR7-4-DD-55H-AU-13

for example for Tubular Halfshaft Part No. 28130049

Station 1,                       reduce OD and wall in center section infeed 

swaging R10-4            (parallel operation on stations 1 and 2)

Station 2,                       reduce OD and wall in center section infeed 

swaging R10-4            (parallel operation on stations 1 and 2)

Station 3,                       station to load parts from station 1 or

transfer station                  from station 2 into station 4

Station 4,                       pre-form form first end infeed swaging R7-4

Station 5,                       finish form first end plunge swaging 

UR7-4-DD

Station 6,                       external spline first end axial forming 

HU-40

Station 7,                       face and chamfer first end, turn and deburr

turning                         groove in spline area

Station 8,                       turn shaft 180°

turnaround station

Station 9,                       pre-form second end infeed swaging R7-4

Station 10,                      finish form second end plunge swaging 

UR7-4-DD

Station 11,                      external spline second end axial forming 

HU-40

Station 12,                      face and chamfer second end, turn and deburr

turning                         groove in spline area

Station 13,                      boot grooves both sides rolling

Remarks:                       OD and wall reduction in center section is 

carried out in simultaneous operation on stations 1 and 2 in order to reduce total cycle time for 

this longest operation (approx. 35 sec. per op. I station) to 50%, thus cycle time of entire 

transfer line corresponds to shorter cycle time (18 sec.) of stations 4 - 13

Cycle time:                     18 seconds per piece - (reference this time as per Nexteers' piece part)

 13-Station Transfer Swaging Machine R10-4/UR7-4-DD-55H-AU-13:

1.1        Automation System:

1.1.1      Bunker:

Installed  in  front  of  the  input  conveyor  outside  of  the  noise  and  safety 

enclosure (see additional features below).

Capacity about 120 pieces with outside diameter 044 mm.

Equipped with loading device to separate the workpieces and to transfer them onto the input 

conveyor.

1.1.2      Transfer System:

Linear  transfer  system  for  automatic  workpiece  transport  from  the  input conveyor  

into station 1 and 2 (parallel operation), from station 1 or 2 into station 3 (transfer 

station), and simultaneously from station 3 - 13 and from the last station to the machine exit.

All transfer grippers are hanging vertically from top to bottom.

The transfer system can be pivoted up for tool change, maintenance, etc.

1.1.3      Conveyors:

1.1.3.1    Input Conveyor:

Conveyor  to transport  the workpieces from  outside the noise and safety enclosure into 

the first transfer gripper of the machine.

1.1.3.2    Exit conveyor:

Conveyor to transport the workpieces from the machine to the outside of the noise and 

safety enclosure.

The conveyor can be inclined to drain off lubrication oil from the inside and outside 

of the workpiece.

1.2        Station 1:  Swaging Station R10-4

1.2.1      Swaging machine R10-4:

Infeed swaging machine for axial infeed swaging operations.

Internal rotating machine with rotating spindle and stationary outer ring.

Heavy-duty 4-die swaging machine with dies dimension 100 x 100 x 250 mm (width x height x 

length).

Actively driven cage rollers for high output and reduced wear.

1.2.1.1    Hydraulic counter-pusher / mandrel device installed at the rear of the swaging 

machine, device reaching through the machine spindle.

Equipped with linear encoder for control of the positions (programmable).

1.2.2  Feeding system: 

Hydraulic feeding system type 55H for workpiece infeed. 

 Equipped with linear encoder and servo-hydraulic cylinder for control of the 

positions (programmable) and speeds (programmable).   

1.2.2.1 Feeder jaw: 

Hydraulic workpiece clamping device with two radial parallel jaws on the slide 

of the feeding system. 

 The clamping pressure is continuously adjustable for controlled rotational 

speed of the workpiece during swaging. 

1.2.2.2 Mandrel device: 

Hydraulic mandrel device on the slide of the feeding system. 

 Mandrel device used for calibration of workpiece bore sizes, for wall thickness 

reductions, and for swaging of internal profiles with tight tolerances.   

Equipped with linear encoder for control of the positions (programmable).   

1.3 Station 2:  Swaging Station R10-4 

Station identical to station 1, see item 1.2 

1.4 Station 3:  Transfer Station  

Station to take over the parts from station 1 or station 2 (parallel operation) 

from the first unit of the transfer system and to transfer them into the second 

unit of the transfer system for loading into station 3. 

1.5 Station 4:  Swaging Station R7-4 

1.5.1 Swaging machine R7-4: 

Infeed swaging machine for axial infeed swaging operations. 

Internal rotating machine with rotating spindle and stationary outer ring. 

Heavy-duty 4-die swaging machine with dies dimension 70 x 70 x 150 mm 

(width x height x length). 

Actively driven cage rollers for high output and reduced wear.  

1.5.1.1 Hydraulic counter-pusher / mandrel device installed at the rear of the swaging 

machine, device reaching through the machine spindle. 

 Equipped with linear encoder for control of the positions (programmable). 

1.5.2  Feeding system: 

Hydraulic feeding system type 55H for workpiece infeed. 

 Equipped with linear encoder and servo-hydraulic cylinder for control of the 

positions (programmable) and speeds (programmable).   

1.5.2.1 Feeder jaw: 

Hydraulic workpiece clamping device with two radial parallel jaws on the slide 

of the feeding system. 

 The clamping pressure is continuously adjustable for controlled rotational 

speed of the workpiece during swaging. 

1.5.2.2 Mandrel device: 

Hydraulic mandrel device on the slide of the feeding system. 

 Mandrel device used for calibration of workpiece bore sizes, for wall thickness 

reductions, and for swaging of internal profiles with tight tolerances.   

Equipped with linear encoder for control of the positions (programmable).   

1.6 Station 5:  Swaging Station UR7-4-DD 

1.6.1 Swaging machine UR7-4-DD: 

Plunge swaging machine for radial plunge swaging operations and for axial 

infeed swaging operations. 

Double-rotating machine with rotating spindle and rotating outer ring. 

Heavy-duty 4-die swaging machine with dies dimension 70 x 70 x 150 mm 

(width x height x length). 

Actively driven cage rollers for high output and reduced wear.  

Machine equipped with locking system for the spindle enabling to produce also 

non-circular external cross-sections. 

Hydraulic plunging device for opening and closing the swaging dies radially. 

The radial movement of the swaging dies is executed by moving the tapered 

outer strikers axially along the tapered axially stationary wedges (patented). 

When the plunging device remains stationary (by selecting the corresponding 

machine program), the machine can alternatively also be employed as an 

infeed swaging machine.   

Outer strikers and swaging dies are mechanically linked (patented). 

The strikers have a special movement which separates the strikers from the 

rollers when the dies are radially open, thereby no noise and no wear when the 

machine is idling (patented). 

 Equipped with linear encoder and servo-hydraulic cylinder for control of the 

closing and opening positions (programmable) and speeds (programmable) of 

the plunging device.   

1.6.1.1 Hydraulic counter-pusher / mandrel device installed at the rear of the swaging 

machine, device reaching through the machine spindle. 

 Equipped with linear encoder for control of the positions (programmable).  

1.6.2  Feeding system: 

Hydraulic feeding system type 55H for workpiece infeed. 

 Equipped with linear encoder and servo-hydraulic cylinder for control of the 

positions (programmable) and speeds (programmable).   

1.6.2.1 Feeder jaw: 

Hydraulic workpiece clamping device with two radial parallel jaws on the slide 

of the feeding system. 

 The clamping pressure is continuously adjustable for controlled rotational 

speed of the workpiece during swaging. 

1.6.2.3 Slide lock: 

Hydraulic device to lock the feeder slide axially during plunge swaging to 

obtain precise swaging positions.  

1.7 Station 6:  Hydraulic Axial Forming Station HU-40 

1.7.1 Forming unit HU-40: 

Horizontal hydraulic forming cylinder with die retainer to take up one external 

forming die for example for production of external splines. 

System for easy and quick exchange of the forming die. 

Linear encoder and servo-hydraulic cylinder for control of the positions 

(programmable) and speeds (programmable) of the forming die. 

Max. forming force: 400 kN  

Max. forming stroke: 150 mm  

1.7.1.1 Mandrel device installed at the rear of the forming unit. 

Concentric system through the piston of the main forming cylinder. 

The mandrel is used for calibration of the inside diameter under the externally 

formed (spline) workpiece area. 

1.7.2  Clamping device: 

Hydraulic radial clamping device for concentric clamping of the workpiece 

directly in front of the forming area. 

The clamping device is rigidly connected with the forming unit via four columns. 

1.7.3  Feeding system: 

Hydraulic feeding system for loading the workpieces into the radial clamping 

device.  

 Equipped with linear encoder and servo-hydraulic cylinder for control of the 

positions (programmable) and speeds (programmable).   

1.7.3.1 Feeder jaw: 

Hydraulic workpiece clamping device with two radial parallel jaws on the slide 

of the feeding system. 

 The clamping pressure is continuously adjustable. 

1.8 Station 7: Turning Station

Turning station for facing and chamfering of the workpiece end, for production

of circular grooves and undercuts and for deburring of turned grooves in

external splines.

(NOTE TO BUYER. THIS STATION WAS UPGRADED TO SMS TURNING STATION. )

1.8.1 Turning unit:

Unit operating with rotating workpiece and stationary tooling.

Equipped with rotationally driven chuck to clamp and rotate the workpiece

during the turning operation. The rotational speed of the chuck is electronically

adjustable.

Slide unit for end facing and chamfering and for production of grooves.

One radial slide with deburring wheel for removal of burrs on turned grooves

located in the area of external splines.

The infeed positions and speeds of the cutting slides are programmable.

(NOTE TO BUYER. THIS STATION WAS UPGRADED TO SMS TURNING STATION.)

1.8.2 Feeding system:

Feeding system for infeed and outfeed of the workpieces into the chuck.

Adjustable quick speed and slow speed for both movement directions.

The feeder movements are programmable.

1.8.2.1 Hydraulic workpiece clamping device with two radial jaws installed on the slide

of the feeding system.

1.8.3 Magnetic chip removal conveyor installed at the rear of the turning unit.

1.9 Station 8: Turnaround Station

Station to change the workpiece orientation 180° after forming the first

workpiece end on stations 1-7 for processing of the opposite, second

workpiece end on stations 9-13.

Equipped with rotation cylinder with gripper, and with axial positioning cylinder

to move the workpiece into a defined axial position after rotation.

1.10 Station 9: Swaging Station R7-4

Station identical to station 4, see item 1.5

1.11 Station 10: Swaging Station UR7-4-DD

Station identical to station 5, see item 1.6

1.12 Station 11: Hydraulic Axial Forming Station HU-40

Station identical to station 6, see item 1.7

Page 10 of 14

1.13 Station 12: Turning Station

Station identical to station 7, see item 1.8

(NOTE TO BUYER. THIS STATION UPGRADED TO SMS TURNING STATION)

1.14 Station 13: Rolling Station

Station for simultaneous rolling of boot grooves on both workpieces ends.

1.14.1 Double-sided rolling unit with rolling head mounted on a robust spindle unit.

Hydraulic slide units for axial positioning of the rolling units over the workpiece

ends, with adjustable and programmable speeds and positions.

1.14.2 Hydraulic workpiece clamping device.

1.15 Machine base.

1.16 Hydraulic power station at the side of the machine.

Oil tank equipped with heat exchanger oil / water and with oil heating.

Central unit with 5 zones.

1.17 System for operation under oil-flush, with oil tank, pump, filters, heat exchanger

oil / water and oil heating.

1.18 Centralized lubrication system for all slides.

1.19 Electrical cabinet at the side of the machine.

PLC controls system for control of all positions and movements.

Programs for setting and for automatic operation.

1.20 Machine monitoring and diagnostic system on the control panel.

Display text in English language.

1.21 Machine capable of producing workpieces within the following dimensional

range (other dimensions are possible within certain limits, to be discussed):

- outside dia. of input part: min. 30.0 mm – max. 55.0 mm

- workpiece length: min. 350 mm – max. 900 mm

1.22 Equipment components (details to be discussed):

- PLC: Allen-Bradley

- Operator panel: Allen-Bradley

- Electric motors: Siemens

- Proximity switches: Balluff

- Hydraulic components: Vickers

- Hydraulic cylinders: HMP, Hänchen

- Pneumatic components: Festo

- Central lubrication system: Willy Vogel or Trabon

2. Additional Features: Fire suppression installed at Nexteer. 

2.1 Noise and safety enclosure:

Enclosure covering the entire machine. The enclosure is used to reduce the

noise level and simultaneously also acts as safety device according

international safety standards.

Equipped with doors for access to the machine and with windows for visual

control. The doors are equipped with safety switches.

Equipped with lighting and with fans for exchange of air.

Max. noise level outside in about 1 m distance from the enclosure:

80 dB (A) during automatic machine operation

2.2 Drip pan with floor gratings:

Drip pan covering the entire floor surface area inside the enclosure, with floor

gratings in the areas between machine and enclosure walls.

2.3 Additional cleaning station:

Additional station installed at the last position of the transfer line.

Air blow off system for internal and external removal of oil on and inside the

workpiece. No dripping after cleaning. Achieved by vacuum system.

Oil is then returned to central coolant system.

2.4 Additional neck down swaging station:

Additional swaging station installed after station 2 to neck down the center

section of halfshafts from 36 mm OD to 28 mm OD, 63.36 mm long.

Plunge swaging station UR7-4-DD, identical to station 5, see item 1.6

This is included as station 11.

2.5 Overhead Crane for change over.

2.6 Note to Buyer. The fire suppression system installed by Nexteer will

only include the parts of the system that installed inside the enclosure.

No external components are included in the sale. Buyer may be able

to hook up fire suppression system inside the room which is included in the

sale to their own central in plant system.

REMOVAL:

Removal of HMP swaging line to take place within 30 days from date of sale.

STORAGE:

Storage if required after removal and prior to shipment can be arranged

some storage space is available at Nexteer in Saginaw, MI at no additional costs

to buyer. Transportation costs to Storage Location is the buyer's responsibility.

Storage time is limited and to be used as a buffer as buyer continues with timely

removal and shipment of all components and related equipment to their facilities.

PAYMENT TERMS:

Buyer shall pay 50% of purchase price prior to start of Removal.

Ownership/Title for the equipment will pass to Buyer upon receipt of the initial 50% down payment with order.

Remaining 50% shall be paid prior to the Property being removed from Nexteer Facility.

THIS ITEM IS OFFERED FOR SALE SUBJECT TO PRIOR SALE AND

BUYER'S UNCONDITIONAL ACCEPTANCE OF SELLERS TERMS

AND CONDITIONS.

RAB INDUSTRIES, INC.